IBM / Lenovo IMM (Integrated Management Module) Default Username and Password
KB ID 0001088 Problem I’m more used to HP servers with iLO’s and Dell servers with DRAC’s, but today I had to put in an IBM System X (now Lenovo) Server with an IMM on it. Once I’d got its IP address from my DHCP servers list of leases I was faced with a logon screen. Solution Took some hunting, but the credentials are as follows; Username: USERID Password: PASSW0RD (That’s a zero, not an ‘O’...
Change Hosts / Connection / Screens on a Belkin Omniview KVM Switch
KB ID 0000194 Problem You are stood in the server room looking like a muppet, because you can’t switch between servers on the Belkin KVM switch, and even though the HP/Fujitsu KVM switches all work with [Print Scrn], these don’t. And putting a model number or something on the exposed part of the KVM so you could Google it and get a handbook would have been far too hard. Solution You need to Press Scroll Lock TWICE {it...
Juniper SRX Firewall – Allow ‘Ping’
KB ID 0000706 Problem I was working on an SRX100B Firewall yesterday, and needed to be able to ping the outside interface. Solution Note: You can quickly enable ping on a physical interface from CLI like so; set security zone security-zone trust interface ge-0/0/0 host-inbound-traffic system services ping 1. Log into the web console of the Juniper. 2. Navigate to Security > Zones/Screen > Select the ‘Untrust’ Zone...
Juniper SRX Firewall – Allow Web Management from Outside
KB ID 0000708 Problem Assuming you already have web management enabled, and you want to access it from the outside (the untrusted zone). Solution 1. Log into the web console of the Juniper. 2. Navigate to Security > Zones/Screen > Select the ‘Untrust’ Zone > Edit > Host inbound traffic – Interface > Select the Outside interface > Under Interface services add in ‘http’ > OK. 3. Then...
Factory Reset Juniper SRX Firewall
KB ID 0001003 Problem If you manage to stuff up your firewall, or you have just done some testing and want to revert back to ‘as new’ here is how to do it. Solution 1. Connect to the firewall either by console cable or via SSH, go to CLI mode then configuration mode. login: PeteL Password: ************ — JUNOS 12.1X47-D10.4 built 2014-08-14 22:21:50 UTC PeteL@Petes-SRX> cli PeteL@Petes-SRX> configure Entering...
JunOS – Using TACACS+ With Cisco ACS
KB ID 0001040 Problem I’ve been configuring a client’s Juniper SRX chassis cluster, for a while now. Their ACS was deployed last week so my task was to configure it to use the TACACS+ from the Cisco ACS server. The client’s setup required them to use their fxp0 management interfaces to perform the authentication. After it was configured and working, (due in no small part, to the ACS skills of Mr SteveH). I decided...
Juniper SRX – Setting the Default Static Route
KB ID 0001008 Problem It takes me seconds to do this on an ASA, on every occasion I’ve had to do the same on a Juniper firewall I’ve had to research how to do it again. Here I’m setting up the ‘default’ route to the Internet, but the syntax is the same for setting up any static route. Solution 1. Connect to the firewall either by console cable or via SSH, go to CLI mode then configuration mode....
Juniper SRX – ‘The Routing Subsystem Is Not Running’
KB ID 0001045 Problem While trying to deploy Solarwinds to monitor a Juniper SRX failover cluster, we were having no joy connecting to the management interface of the secondary/standby firewall. The management (fxp0) interface on the primary (node0) firewall we could get to OK. ] After jumping on the secondary firewall (via the console connection) we observed the following; error: the routing subsystem is not running Solution As you...
HP E Series Wireless – Cannot Access Local LAN
KB ID 0000486 Problem You have an HP HP E-Series Mobility E-MSM460, 466 & 430 Access Point, and you cannot access resources on your local LAN (though internet access works fine). This is default “Out of the box” behavior, a lot of consumers want to provide wireless access but DONT want the wireless clients having access to their local servers. That’s fine but what if you do? Solution 1. Log into the web...
Setup and Configure HP Wireless E-MSM720 Wireless Controller with HP E-MSM430 Access Points
KB ID 0000692 Problem We got some ‘demo stock’ in the office this week, I don’t do a lot of wireless, so I thought I would get it setup and have a look to see how easy/difficult it was. Hardware used HP E-MSM720 Premium Mobility Controller (J9694A) HP E-MSM 430 Wireless N Dual Radio Access Point (J9651A) HP HP 2915-8G-P-o-E Switch (J5692A) The switch and controller are ‘tiny’ so if you want to put them...