Veeam Repository: ReFS with 64 KB Block Popup
KB ID 0001452 Problem When adding a ‘Backup Repository’ to Veeam you may see one of the following; The file system on the specified volume does not support fast cloning. We recommend using ReFS volume formatted with 64 KB cluster size. Proceed anyway? The specified ReFS volume is formatted with 4 KB cluster size. We recommend formatting the volume with 64 KB cluster size. Proceed anyway? Solution Without going into what...
Exchange Update / Install Error: The Error Code Is 8224
KB ID 0001451 Problem I saw this error while attempting to install an update on Exchange 2010, but it can be seen on all flavours of Exchange. This is the ‘gist’ of the error; Organization Preparation Failed Error: The following error was generated when “$error.Clear(); install-ExchangeSchema -LdapFileName ($roleInstallPath + “Setup\Data\”+$RoleSchemaPrefix + “schema0.ldf”) ” was run:...
VMware Fusion: Guest VM ‘Lost’ Network Connectivity
KB ID 0001450 Problem I keep a Windows 10 VM on my laptop, and last week it lost network connectivity, (it’s set to get its IP from my mac and get network connectivity via NAT). The guest was getting a 169.254.x.x APIPA address so either NAT was down, or there was no network? Solution You need to ‘Restart’ the services on the Mac host machine. Execute the following two commands;...
O365: Enable Application Impersonation
KB ID 0001449 Problem While using a migration tool to do some ‘on-prem’ to Office 365 migrations I had to enable ‘Application Impersonation’ for my Office 365 user. The tool didn’t explain how to do that, so I had to work it out for myself 🙁 So to make things easier for everyone else, here’s how to do it. Solution From within the Office 365 portal > Admin > Exchange. Dashboard > Permissions...
AD Sites and Services: ‘Show Services Node’ Missing?
KB ID 0001448 Problem While working on an old Exchange system this week I wanted to take a look at the ‘autodiscovery’ SCP in AD Sites and Services. Read any post, and you will se that you need to enable ‘Services Node View’ in AD sites and services. To do that you simply right click then go to View > Show Service Node. However, I didn’t get that option? Solution This was driving me crazy for a while,...
Exchange 2010 Stops Working after 6 – 12 Hours Uptime
KB ID 0001447 Problem If your Exchange 2010 Server Stops working after a 6 to 12 hour window, then this is a known problem caused by last months (July 2018) security updates. You will also notice that the ‘transport service’ becomes unresponsive. Note: A reboot will temporarily fix the problem but the server then ceases to function after the same time. Solution Which update you need to uninstall, depends on your operating...
Cisco ASA: VPNs With Overlapping Subnets
KB ID 0001446 Problem I’ve seen this pop up a few times in forums, and I’ve even seen people post “It cant be done, you will need to change one of the subnets,” but to be honest, it’s not that difficult. We simply have to do some NAT. This is the bit people struggle with, with VPNs usually we need to STOP NAT being applied to VPN traffic, and we still do, we simply NAT the traffic before we sent it over...
Cisco ASA ‘Ping Source?’
KB ID 0001445 Problem To be honest, the title is a little misleading, on an ASA you can specify which interface to launch a ‘ping’ from, but that’s it. I found myself in a situation today where I was working on a client firewall and I was trying to bring up a VPN tunnel, and I did not have access to any of their machines, and nor did they, (hence the reason for the VPN tunnel!) Well we can’t use good old...
Cisco Stacking 2960-X Catalyst Switches
KB ID 0001444 Problem You can stack up to 8 2960-X Switches*, you will require the stack modules and cables, (shown below). *Note: If you are studying for an exam, and the question is StackWize the answer is 9. Solution Stack Modules: Power down the switch, remove the blanking plate and fit the module, then when powered on you can use a show inventory command to make sure the module has been detected correctly. Switch#show inventory...
HP BL460c (Gen 10) Blade No RAID?
KB ID 0001443 Problem While spinning up some new BL460c (Gen 10) blades for a client, I noticed there was no RAID option? They were going to be VMware ESX hosts, and had two SSD drives so I just accepted the default and my ESX server saw a LUN for each drive and I created two DataStores on each host. The client wanted them changing to RAID1 (fair enough) so I revisited the drive setup. Solution WARNING: Before you proceed enabling...